+- MG Snowboard. Forum Snowboard (https://www.mgsnowboard.com/forum)
+-- Forum: MG Snowboard Forum (/forumdisplay.php?fid=3)
+--- Forum: Regolazioni Snowboard, set-up e riparazioni (/forumdisplay.php?fid=16)
+--- Discussione: GUIDA AL P-tex questo sconosciuto !!!! (/showthread.php?tid=4488)
GUIDA AL P-tex questo sconosciuto !!!! - zonaradioattiva - 30-01-2010 03:24 PM
dopo il successo della mia guida su come
SCIOLINARE
vi propongo la seconda ed importante parte per fare di tutti noi dei perfetti ski man
quindi ecco la mia guida COME RIPARARE LA SOLETTA COL P_TEX
RE: GUIDA AL P-tex questo sconosciuto !!!! - quadramon - 30-01-2010 05:00 PM
grande zona
puoi fare anche la guida sulla stampa di euro falsi...mi interessa molto
RE: GUIDA AL P-tex questo sconosciuto !!!! - Lelito - 30-01-2010 06:22 PM
grande zona...macgyver ti fa na pippa
RE: GUIDA AL P-tex questo sconosciuto !!!! - Fusca Freestyle - 30-01-2010 07:32 PM
Fai brutto alle scimmie urlatrici
ma sto p-tex è una specie di polimero simile a quello della soletta?
RE: GUIDA AL P-tex questo sconosciuto !!!! - zonaradioattiva - 30-01-2010 07:50 PM
(30-01-2010 07:32 PM)Fusca Freestyle Ha scritto: Fai brutto alle scimmie urlatrici
http://www.mgsnowboard.com/soletta.htm
leggete qui c'e' la spiegazione di cos'e' sto magico elemento chimico
messagi uniti in automatico
(30-01-2010 05:00 PM)quadramon Ha scritto: grande zona
puoi fare anche la guida sulla stampa di euro falsi...mi interessa molto
ci sto' pensando ma per un errore di stampa mi sono venute solo banconote da 30€
RE: GUIDA AL P-tex questo sconosciuto !!!! - Fusca Freestyle - 31-01-2010 03:47 PM
huauhauhauhahahu e vabbeh dai chi vuoi che se ne accorga
RE: GUIDA AL P-tex questo sconosciuto !!!! - zonaradioattiva - 05-03-2010 04:22 PM
dato che in molti continuano a chiedere.... date un okkio alle guide all'inizio della discussione
RE: GUIDA AL P-tex questo sconosciuto !!!! - scraby - 08-08-2010 02:15 PM
ma si le banconote da 30 passeranno sicuramente inosservate!!!!!
..ma ragazzi non lo sapete che lui è chuck norris??ahahahahahah..comunque belle le guide
RE: GUIDA AL P-tex questo sconosciuto !!!! - xiaobao - 20-08-2010 09:08 AM
I looked on line for instructions to locate and replace the knock sensor, but couldn't find anything on my year, so I'm posting this to help anyone who may benefit from it. I talked to a service tech at my local Mazda dealer to find out where the sensor is located...behind the intake manifold. To replace the knock sensor you have to remove the intake manifold. Good news was that you don't have to completely remove it from the engine burberry compartement, just take all of the bolts loose remove some wiring harness hold down fasteners, removing the rubber bellows type air intake from the throttle body, and after removing about 8 or 9 bolts. One of bolt can prada only be reached from under the car after removing the splash guard. Another one is in the middle of the manifold and is only accessible through the opening provided in the manifold to reach it. But, it required an inpsection mirror to see the bolt and manipulate the socket onto it. Purchase an intake manifold gasket kit, in case you need it. Each port on the intake has its own green plastic gasket. Mine came off without damage to any gasket and I just returned the unopened box for full credit, about $25 via the local autoparts store. louis vuitton
RE: GUIDA AL P-tex questo sconosciuto !!!! - zonaradioattiva - 04-09-2010 08:30 PM
[quote='xiaobao' pid='32674' dateline='1282288085']
I looked on line for instructions to locate and replace the knock sensor, but couldn't find anything on my year, so I'm posting this to help anyone who may benefit from it. I talked to a service tech at my local Mazda dealer to find out where the sensor is located...behind the intake manifold. To replace the knock sensor you have to remove the intake manifold. Good news was that you don't have to completely remove it from the engine burberry compartement, just take all of the bolts loose remove some wiring harness hold down fasteners, removing the rubber bellows type air intake from the throttle body, and after removing about 8 or 9 bolts. One of bolt can prada only be reached from under the car after removing the splash guard. Another one is in the middle of the manifold and is only accessible through the opening provided in the manifold to reach it. But, it required an inpsection mirror to see the bolt and manipulate the socket onto it. Purchase an intake manifold gasket kit, in case you need it. Each port on the intake has its own green plastic gasket. Mine came off without damage to any gasket and I just returned the unopened box for full credit, about $25 via the local autoparts store. [url=http://www.louisvuitton-sale.com/]louis vuitton[/url
Thank you for your explanation but that 's not a forum for car repairers